principle of flow造句
例句與造句
- The principle of flow cytometer and its clinical application
流式細胞儀工作原理及臨床應用 - On the basis of the principle of flow tomography reconstruction , a simulation to the whole process is conducted and a 0 . 0726 rms error is obtained
在介紹哈特曼流場層析重建原理的基礎上，對流場重建的整個過程進行了計算機仿真，重建的rms誤差為0 . 0726 。 - The flowmeters based on the principle of flow vibration are widely used . however , they are easily subjected to noises caused by pipe vibrations and fluid turbulence
基于流體振蕩原理的流量計應用相當廣泛，但是，易受管道振動和流體擾動等噪聲的影響。 - From the basic principle of flow , we can build two compartmental models between intermission and sequent ; and as well as develop the simulation software
從水流的基本特性出發，分別建立了間歇操作和連續操作水箱（池）的分區數學模型，并在此基礎上進行了計算機仿真應用軟件的開發。 - The principle of flow measurement is also presented . based on general pc - based programmable controller , the general and flexible measure - control field unit is developed , which has specialty characteristics and is suitable for different water measuring devices
為適應在不同的測流方式下的數據采集和流量計算，采用通用的pc - based可編程控制器，用c語言開發出具有專業特色、通用、靈活的測控一體現場單元。 - It's difficult to find principle of flow in a sentence. 用principle of flow造句挺難的
- This paper introduces the working principle of the pouring machine designed for the microwave oven , including the principle of flowing route of gas and liquid the designs of proportion - adjusting setup of pouring machine , xy planar worktable and plc control are introduced in this paper
論文介紹了微波爐灌封設備的工作原理，包括氣路原理和液路原理。介紹了灌封設備的兩種膠的比例調節機構、 xy二維工作臺、 plc控制的設計。 - A hardware structure of outdoor controllers of a dc frequency converting air conditioner was introduced , which was based on mb90f562 single chip computer , the function of each unit circuit is presented , the principle of flow changing process of a nonposition dc and brushless motor is emphatically analyzed
摘要介紹了基于單片機mb90f562驅動的直流變頻空調室外控制器硬件結構，說明了各單元電路的功能，著重分析了無位置直流無刷電機換流過程及原理。 - This paper analyses the type , function and characteristics of usual proportional control valves and raises a new modificative version in the light of their drawback . that is , basing on the principle of flow amplification and electrical feedback and throughout calculation and analysis on flow closed loop control and pressure flow combination . , determination of the minimum controlled pressure difference as well as flow controlling range and structure of main valve and research of the dynamic and static characteristic , the paper puts forward control principle of " flow - load pressure change - displacement revision " and pressure / flow double closed loop , and further expounds that using a proportional controller and a electric mechanical transducer can separately serve the control function of pressure or flow as well as flow pressure combination
本論文分析了目前常用比例閥的類型、功能、特性，并針對其不足提出新的改進方案，即：以流量放大，電反饋兩個原理為基礎，通過對流量閉環控制及壓力流量復合的計算分析、確定上最小控制壓差及流量控制范圍，確定主閥結構、功能特性研究等，提出了“流量? ?負載壓力變化? ?位移修正”的控制原理和壓力流量雙閉環控制原理，并進一步論述了利用一個比例控制器和一個“電?機械轉換器”就可完成獨立的壓力或流量控制功能以及流量壓力復合控制功能。 - Abstract : in order to eliminate the product defects such as deformation , corrugation and rupture , the authors put forward the principle of flow rate uniformity for the design of rubber and plastics profile extrusion dies . on the basis of this principle and through the rheologic analysis of some actual cases , the design procedure is demonstrated
文摘:為解決擠出制品的扭曲變形、起皺、破裂等問題，本文提出了橡塑異型材擠出口模設計的流率平衡原則，并據此原則通過對具體例子的流變學分析，提出了口模設計方法。